AP
AR
AT
AU
4-5/8"
[117.5 mm]
15/16"
[23.8 mm]
2-1/2"
[63.5 mm]
1-1/4"
[31.8 mm]
31/32"
[24.6 mm]
ANTI-LIFT
CFT-211-WB
2"
[50.8mm]
1"
[25.4 mm]
29/32" [23 mm]
MIN 3/8" [9.5 mm]
C-914
GUIDE
CHANNEL
C-913 GUIDE
3/8"
[9.5 mm]
W
A
L
L
1/4"
[6.4 mm]
2" [50.8 mm] x
1/4" [6.4mm]
FLAT BAR
4"
[101.6 mm]
3/8" [9.5 mm]
4-3/4" [120.7 mm]
CFT-210 SHOCK
ABSORBING STOP
MIN 5" [127 mm]
THREADED END
STEP 4
M
I
N
5
"
[
1
2
7
m
m
]
STEP 8
STEP 9
INSERT 1/8"
ALLEN KEY
HERE
STEP 10
B
A
C
K
F
A
C
E
O
F
1
-
3
/
4
"
O
R
T
H
I
C
K
E
R
D
O
O
R
S
B
A
C
K
F
A
C
E
O
F
1
-
3
/
8
"
T
H
I
C
K
D
O
O
R
S
1/16" [1.6 mm]
1/4" [6.4 mm]
MAX
CFT-201 TOP MOUNT
HANGER SCREW HOLE
LOCATION TEMPLATE
STEP 5
CFT-201 TOP MOUNT HANGER SLIDING DOOR KIT
K.N. CROWDER MFG. INC.
1220 BURLOAK DRIVE
BURLINGTON, ONTARIO, CANADA, L7L 6B3
TELEPHONE: 905-315-9788 - FAX: 905-315-8090
TOLL FREE FAX: 1-800-567-0123
K.N. CROWDER INC.
210 EIGHTH STREET SOUTH
LEWISTON, NEW YORK, U.S.A. 14092
TELEPHONE: 1-716-754-8247
TOLL FREE FAX: 1-800-567-0123
WEBSITE: www.kncrowder.com --- E-MAIL: customerservice@kncrowder.com
PARTS LIST (FOR 1 DOOR KIT)
CFT-201 HANGER (2)
STEP 1
DETERMINE OPENING SIZE, DOOR SIZE & WALL HEIGHT BASED ON DIMENSIONS SHOWN IN DETAIL VIEWS AND CLEARANCE REQUIRED BELOW DOOR. TRACK
SHOULD BE AT LEAST TWO TIMES DOOR WIDTH. EXAMPLE: 36" DOOR REQUIRES 72" TRACK. TRACK LENGTHS ARE ONLY AVAILABLE IN PER FOOT INCREMENTS.
CFT SERIES TRACK MUST BE INSTALLED ONTO SOLID BACKING/SUPPORT (IN WALL). [FOR DRYWALL/WOOD BACKING, SEE SEPARATE INSTRUCTION SHEET]
STEP 2
ONCE DOOR SIZE HAS BEEN DETERMINED, CALCULATE THE DISTANCE FROM THE FINISHED FLOOR TO THE CENTER OF THE TRACK WITH THE FOLLOWING
FORMULA: (NOTE: MINIMUM GROUND CLEARANCE IS 3/8" [9.5 mm], 1/2" [12.7 mm] IS USED FOR CALCULATION EXAMPLE)
DOOR HEIGHT (A) + 2-1/2 [63.5 mm] + MINIMUM 1/2" [12.7 mm] GROUND CLEARANCE (B) = DISTANCE TO CENTER OF TRACK.
EXAMPLE FOR 84 [2134 mm] DOOR: 84 [2134 mm] (A) + 2-1/2 [63.5 mm] + 1/2" [12.7 mm] = 87" [2210 mm] FROM FINISHED
FLOOR TO CENTER OF TRACK.
STEP 3 (THIS STEP APPLIES TO 5/16"-18 EXPANSION SHIELD ONLY)
MARK A HORIZONTAL LINE WITH A LEVEL ON WALL AT THE MEASUREMENT CALCULATED IN STEP 2.
LOCATE TRACK ON WALL AND MARK HOLE LOCATIONS AS PER SPACING SHOWN IN THE
LEGEND OR WITH TRACK. DRILL 5/8 HOLE AT LEAST 2 DEEP AT THE LOCATIONS MARKED.
STEP 4 (THIS STEP APPLIES TO 5/16"-18 EXPANSION SHIELD ONLY)
INSERT ONE 5/16-18 EXPANSION SHIELD (SUPPLIED) INTO EACH HOLE.
NOTE: INSERT WITH THREADED END INTO THE HOLE FIRST.
STEP 5
PLACE ONE CFT-211-WB (WALL BRACKET) ON EACH HOLE ON THE BACK OF THE TRACK
(COUNTERSUNK SIDE ON TRACK IS THE FRONT FACE) WHILE PUTTING ONE 5/16-18 X 3
FLAT HEAD SOCKET SCREW THROUGH THE FRONT HOLE.
STEP 6
LIFT TRACK UP TO WALL AND LOOSELY SCREW THE FLAT HEAD SOCKET SCREWS INTO
THE EXPANSION SHIELDS PLACED IN STEP 4. SECURE TRACK TO WALL BY TIGHTENING
FLAT HEAD SOCKET SCREWS. ENSURE THAT EXPANSION SHIELDS HAVE BEEN
FULLY SEATED.
STEP 7
PREPARE BOTTOM OF DOOR & INSTALL C-914 GUIDE CHANNEL.
SEE OPTION #1 ON THE C-913/C-914 INSTRUCTION SHEET FOR MORE DETAILS.
STEP 8
LOCATE & INSTALL CFT-201 TOP MOUNT HANGERS ON DOOR
MINIMUM 5 FROM CENTER OF HANGER TO EDGES OF DOOR
WITH FOUR #10 X 2 FLATHEAD SCREWS (PER HANGER).
STEP 9
PLACE DOOR ONTO TRACK. THE FLAT IN THE GROOVE
OF THE WHEEL SHOULD BE RESTING ON THE TOP OF
THE FLAT BAR TRACK. INSTALL CFT-201 ANTI-LIFT ONTO
CFT-201 HANGER WITH THE SUPPLIED 5/16-18 X 3/4"
LOW PROFILE HEAD SOCKET CAP SCREW WITH LOCTITE.
NOTE: THE CFT-201 ANTI-LIFT COMPONENT MUST BE
INSTALLED AS THIS WILL PREVENT THE DOOR FROM
LIFTING OFF THE TRACK. USE AN ALLEN KEY TO HOLD
THE ANTI-LIFT (HOLE IN ANTI-LIFT) WHILE TIGHTENING
THE SOCKET CAP SCREW.
STEP 10
INSTALL CFT-210 SHOCK ABSORBING STOPS FROM THE END
OF THE TRACK. LOOSEN THE SCREWS HOLDING THE BACK
CLAMPS TO ALLOW YOU TO SLIDE IT ONTO THE TRACK FROM
THE ENDS. THERE IS ONE LEFT AND ONE RIGHT STOP FOR
EACH DOOR. LOCATE THE STOPS AS REQUIRED TO LIMIT THE
SLIDING DISTANCE OF THE DOOR AND SECURE THE STOP CLAMP
TO THE TRACK WITH THE FOUR SCREWS. NOTE: THE CFT-210 STOPS MUST BE
INSTALLED AS THIS WILL PREVENT THE DOOR FROM RUNNING OFF THE TRACK AND
PROVIDE THE REQUIRED STOPPING FORCE FOR THE DOOR(S).
INSTRUCTION SHEET
FOR 1-3/8" TO 2-1/4" DOORS
SPECIFICATIONS:
-LOAD CAPACITY: 350
LBS PER DOOR.
-FOR SURFACE
MOUNT/BARN STYLE
APPLICATIONS.
-NO HEIGHT
ADJUSTMENT
AVAILABLE ON
HANGER
-IDEAL FOR SOLID
CORE DOORS 1-3/8"
TO 2-1/4" THICK
INSTALLATION INSTRUCTIONS
DIMENSION DETAILS:
CFT-210 SHOCK
ABSORBING STOP
(1 - LEFT & 1 - RIGHT)
CFT-211-WB WALL
MOUNT BRACKET
( )
5/16"-18 EXPANSION
SHEILD ( )
5/16"-18 X 3" FLAT
HEAD SOCKET
SCREW ( )
CFT-200 SOLID
FLAT BAR TRACK
(1 X KIT LENGTH)
5/16"-18 X 3/4" LOW
PROFILE HEAD
SOCKET CAP
SCREW (2)
#10 X 2" PHILLIPS
FLAT HEAD WOOD
SCREW (8)
#10 X 1-1/2"
FLATHEAD
SCREWS (4)
C-914 GUIDE CHANNEL
(1 X DOOR WIDTH)
C-913 FLOOR
GUIDE (1)
CFT-201
ANTI-LIFT (2)
LEGEND
FINISH MAY BE ALL STAINLESS STEEL OR BLACK PLATING DEPENDING ON ORDR.
- QUANTITY IS BASED ON KIT SIZE
-72" KIT INCLUDES 5 SETS (SPACING: 8"[203.2] -14"[355.6] X 4 -8"[203.2])
-84" KIT INCLUDES 6 SETS (SPACING: 7"[177.8] -14"[355.6] X 5 -7"[177.8])
-96" KIT INCLUDES 6 SETS (SPACING: 8"[203.2] -16"[406.4] X 5 -8"[203.2])
-108" KIT INCLUDES 7 SETS (SPACING: 6"[152.4] -16"[406.4] X 6 -6"[152.4])
-120" KIT INCLUDES 8 SETS (SPACING: 7.5"[190.5] -15"[381] X 7 -7.5"[190.5])
-144" KIT INCLUDES 9 SETS (SPACING: 8"[203.2] -16"[406.4] X 8 -8"[203.2])
*
*
*
*
STOP: PLEASE REVIEW ANCHOR TYPE BEING USED BEFORE PROCEEDING.
FOR WOOD ANCHORS, PLEASE REFER TO SEPARATE INSTRUCTION SHEET
AAAA
ABAB
CAUTION:
DO NOT USE IMPACT
DRIVER OR DRILL
WHEN INSTALLING
ANCHOR OR BOLTS
CAUTION:
DO NOT USE IMPACT
DRIVER OR DRILL
WHEN INSTALLING
ANCHOR OR BOLTS
CFT TRACK
K.N. CROWDER MFG. INC.
1220 BURLOAK DRIVE
BURLINGTON, ONTARIO, CANADA, L7L 6B3
TELEPHONE: 905-315-9788 - FAX: 905-315-8090
TOLL FREE FAX: 1-800-567-0123
K.N. CROWDER INC.
210 EIGHTH STREET SOUTH
LEWISTON, NEW YORK, U.S.A. 14092
TELEPHONE: 1-716-754-8247
TOLL FREE FAX: 1-800-567-0123
WEBSITE: www.kncrowder.com --- E-MAIL: customerservice@kncrowder.com
PARTS LIST
5/8" X 1/2" LONG ALUMINUM
SPACER ( )
DRYWALL/WOOD BACKING
INSTALLATION INSTRUCTION SHEET
K.N. CROWDER INC.
210 EIGHTH STREET SOUTH
LEWISTON, NEW YORK, U.S.A. 14092
TELEPHONE: 1-716-754-8247
TOLL FREE FAX: 1-800-567-0123
K.N. CROWDER MFG. INC.
1220 BURLOAK DRIVE
BURLINGTON, ONTARIO, CANADA, L7L 6B3
TELEPHONE: 905-315-9788 - FAX: 905-315-8090
TOLL FREE FAX: 1-800-567-0123
WEBSITE: www.kncrowder.com --- E-MAIL: customerservice@kncrowder.com
*
LEGEND
- QUANTITY IS BASED ON KIT SIZE
-72" KIT INCLUDES 5 SETS (SPACING: 8"[203.2] -14"[355.6] X 4 -8"[203.2])
-84" KIT INCLUDES 6 SETS (SPACING: 7"[177.8] -14"[355.6] X 5 -7"[177.8])
-96" KIT INCLUDES 6 SETS (SPACING: 8"[203.2] -16"[406.4] X 5 -8"[203.2])
-108" KIT INCLUDES 7 SETS (SPACING: 6"[152.4] -16"[406.4] X 6 -6"[152.4])
-120" KIT INCLUDES 8 SETS (SPACING: 7.5"[190.5] -15"[381] X 7 -7.5"[190.5])
-144" KIT INCLUDES 9 SETS (SPACING: 8"[203.2] -16"[406.4] X 8 -8"[203.2])
*
SOLID BACKING
(WOOD)
CFT TRACK
DRYWALL/WOOD BACKING
INSTALLATION INSTRUCTION SHEET
PARTS LIST
5/8" X 1/2" LONG ALUMINUM
SPACER ( )
*
LEGEND
- QUANTITY IS BASED ON KIT SIZE
-72" KIT INCLUDES 5 SETS (SPACING: 8"[203.2] -14"[355.6] X 4 -8"[203.2])
-84" KIT INCLUDES 6 SETS (SPACING: 7"[177.8] -14"[355.6] X 5 -7"[177.8])
-96" KIT INCLUDES 6 SETS (SPACING: 8"[203.2] -16"[406.4] X 5 -8"[203.2])
-108" KIT INCLUDES 7 SETS (SPACING: 6"[152.4] -16"[406.4] X 6 -6"[152.4])
-120" KIT INCLUDES 8 SETS (SPACING: 7.5"[190.5] -15"[381] X 7 -7.5"[190.5])
-144" KIT INCLUDES 9 SETS (SPACING: 8"[203.2] -16"[406.4] X 8 -8"[203.2])
*
SOLID BACKING
(WOOD)
DRYWALL
5/8" X 1/2" ALUMINUM SPACER
5/8" X 1/2" ALUMINUM SPACER IS TO BE INSTALLED
BETWEEN THREAD INSERT AND WALL MOUNT BRACKET.
THIS WILL KEEP INSERT SEATED AND PREVENT
CRUSHING THE DRYWALL.
1/2" DRYWALL
5/16-18 INTERNAL THREAD
INSERT ANCHOR ( )
*
HOLE SIZE IN WOOD
BLOCKING = 13/32" DRILL
THREAD INSERT ANCHOR.
USE 8mm OR 5/16" ALLEN KEY
TO DRIVE INTO SOLID BACKING.
NOTE: THREAD INSERT ANCHOR
FLANGED FACE SHOULD BE
INSTALLED BEHIND DRYWALL
FULLY INTO SOLID BACKING.
ALUMINUM SPACER WILL FILL
THE GAP BETWEEN DRYWALL
& ANCHOR. DO NOT USE IMPACT
DRIVER OR DRILL TO DRIVE
ANCHOR INTO BACKING.
THREAD INSERT ANCHOR DETAILS
5/16-18 INTERNAL THREAD
8mm OR 5/16"
HEX SLOT
EXTERNAL THREAD FOR SECURING
TO SOLID BACKING (WOOD)
13/32" DRILL BIT
RECOMMENDED.
5/16-18 INTERNAL THREAD
8mm OR 5/16"
HEX SLOT
EXTERNAL THREAD FOR SECURING
TO SOLID BACKING (WOOD)
13/32" DRILL BIT
RECOMMENDED.
SOLID BACKING
(WOOD)
THREAD INSERT ANCHOR.
USE 8mm OR 5/16" ALLEN KEY
TO DRIVE INTO SOLID BACKING.
NOTE: THREAD INSERT ANCHOR
FLANGED FACE SHOULD BE
INSTALLED BEHIND DRYWALL
FULLY INTO SOLID BACKING.
ALUMINUM SPACER WILL FILL
THE GAP BETWEEN DRYWALL
& ANCHOR. DO NOT USE IMPACT
DRIVER OR DRILL TO DRIVE
ANCHOR INTO BACKING.
5/8" X 1/2" ALUMINUM SPACER
DRYWALL
5/8" X 1/2" ALUMINUM SPACER IS TO BE INSTALLED
BETWEEN THREAD INSERT AND WALL MOUNT BRACKET.
THIS WILL KEEP INSERT SEATED AND PREVENT
CRUSHING THE DRYWALL.
1/2" DRYWALL
HOLE SIZE IN WOOD
BLOCKING = 13/32" DRILL
5/16-18 INTERNAL THREAD
INSERT ANCHOR ( )
*
SOLID BACKING
(WOOD)
WALL MOUNT BRACKET
CFT-200 TRACK
BOLT
BOLT
CFT-200 TRACK
WALL MOUNT BRACKET
THREAD INSERT ANCHOR
THREAD INSERT ANCHOR
SEE
CRFT-DS
INSTRUCTION
SHEET
SEE
CRFT-DS
INSTRUCTION
SHEET
A PRODUCT OF K.N. CROWDER MFG. INC
K.N. Crowder Mfg. Inc. ●1220 Burloak Drive ● Burlington, Ontario, Canada ● L7L 6B3 K.N. Crowder Inc. ● 210 Eighth Street South ● Lewiston, New York ● 14092
TOLL-FREE PHONE: 1-866-999-1KNC (1562) ● TOLL-FREE FAX: 1-800-567-0123 ● WEBSITE: www.kncrowder.com ● EMAIL: customerservice@kncrowder.com
© 2016 K.N. CROWDER MFG. INC. All Rights Reserved.
CRFT-DS DRYWALL SPACER
INSTRUCTION SHEET
NEW PARTS SUPPLIED IN
CRT & CFT SERIES KITS
1.625 in
[41.28 mm]
PRE-DRILL
CLEARANCE HOLE
IN DRYWALL ONLY
SEE RESPECTIVE
PRODUCT INSTRUCTION
SHEET FOR PRE-DRILL
SIZE IN SUPPORT
1/2" DRYWALL
SOLID BACKING/SUPPORT
(WOOD IS RECOMMENDED)
!!NEW!!
CRFT-DS Ø1-5/8” x 1/2”
ALUMINUM DRYWALL SPACER
INSTALL WITH ‘V’ GROOVE
IN AN UPWARDS POSITION
AS SHOWN BELOW:
CRFT-DS Ø1-5/8” X 1/2” ALUMINUM
DRYWALL SPACER (X)
(SEE RESPECTIVE PRODUCT
INSTRUCTION SHEETS FOR QUANTITY)
OPTIONAL PARTS
AVAILABLE SEPARATELY
1.625 in
[41.28 mm]
PRE-DRILL
CLEARANCE HOLE
IN DRYWALL ONLY
SEE RESPECTIVE
PRODUCT INSTRUCTION
SHEET FOR PRE-DRILL
SIZE IN SUPPORT
1/2" DRYWALL
SOLID BACKING/SUPPORT
(WOOD IS RECOMMENDED)
!!NEW!!
CRFT-DS Ø1-5/8” x 1/2”
ALUMINUM DRYWALL SPACER
INSTALL WITH ‘V’ GROOVE
IN AN UPWARDS POSITION
AS SHOWN BELOW:
CRFT-DS Ø1-5/8” X 5/8” ALUMINUM
DRYWALL SPACER (X)
(FOR 5/8” DRYWALL ONLY. PLEASE
PURCHASE SEPARATELY)
Ø5/8” X 1/2” ALUMINUM
SPACER (X)
(SEE CHART A FOR
QUANTITY BASED ON
TRACK SIZE ORDERED)
ORIGINAL
PART
REPLACED
1.625 in
[41.28 mm]
PRE-DRILL
CLEARANCE HOLE
IN DRYWALL ONLY
SEE RESPECTIVE
PRODUCT INSTRUCTION
SHEET FOR PRE-DRILL
SIZE IN SUPPORT
1/2" DRYWALL
SOLID BACKING/SUPPORT
(WOOD IS RECOMMENDED)
!!NEW!!
CRFT-DS Ø1-5/8” x 1/2”
ALUMINUM DRYWALL SPACER
INSTALL WITH ‘V’ GROOVE
IN AN UPWARDS POSITION
AS SHOWN BELOW:
1.625 in
[41.28 mm]
PRE-DRILL
CLEARANCE HOLE
IN DRYWALL ONLY
SEE RESPECTIVE
PRODUCT INSTRUCTION
SHEET FOR PRE-DRILL
SIZE IN SUPPORT
1/2" DRYWALL
SOLID BACKING/SUPPORT
(WOOD IS RECOMMENDED)
!!NEW!!
CRFT-DS Ø1-5/8” x 1/2”
ALUMINUM DRYWALL SPACER
INSTALL WITH ‘V’ GROOVE
IN AN UPWARDS POSITION
AS SHOWN BELOW:
REVISED STEPS:
AFTER MARKING A HORIZONTAL LINE WITH A LEVEL ON THE WALL
AT THE MEASUREMENT AS PER THE RESPECTIVE PRODUCT
INSTRUCTION SHEETS, LOCATE TRACK ON WALL AND MARK HOLE
LOCATIONS AS PER THE SPACING STANDARDS BASED ON TRACK
LENGTHS FOUND IN CHART A ON THE TEMPLATE SHEET OR WITH THE
TRACK ON SITE.
ONCE THE HOLE LOCATIONS ARE MARKED, PRE-DRILL HOLES INTO
THE WOOD SUPPORT AS REQUIRED ON THE RESPECTIVE PRODUCT
INSTRUCTION SHEETS.
IF THERE IS DRYWALL PRESENT, PRE-DRILL A Ø1-5/8 in [41.3 mm]
CLEARANCE HOLE IN THE DRYWALL PORTION OF THE HOLES ONLY.
SEE ILLUSTRATIONS SHOWN TO THE RIGHT FOR ASSISTANCE.
REVISED STEPS:
INSTALL TRACK ONTO WALL WITH THE
NECESSARY COMPONENTS AND IN THE ORDER
AS SHOWN ON THE RESPECTIVE PRODUCT
INSTRUCTION SHEETS. THE ILLUSTRATIONS
TO THE RIGHT IS BASED ON DRYWALL
APPLICATION. NOTE: ENSURE TRACK IS
LEVELED AND FULLY SECURED TO THE
SUPPORT.
INSTALL THE CRFT-DS DRYWALL SPACERS
WITH THE “V” GROOVE IN AN UPWARDS
POSITION AS PER THE ILLUSTRATION TO
THE RIGHT.
A PRODUCT OF K.N. CROWDER MFG. INC
K.N. Crowder Mfg. Inc. ●1220 Burloak Drive ● Burlington, Ontario, Canada ● L7L 6B3 K.N. Crowder Inc. ● 210 Eighth Street South ● Lewiston, New York ● 14092
TOLL-FREE PHONE: 1-866-999-1KNC (1562) ● TOLL-FREE FAX: 1-800-567-0123 ● WEBSITE: www.kncrowder.com ● EMAIL: customerservice@kncrowder.com
© 2016 K.N. CROWDER MFG. INC. All Rights Reserved.
C-913/C-913-2 SERIES GUIDE SYSTEMS
INSTRUCTION SHEET
AVAILABLE PARTS FOR C-913/C-913-2 GUIDE SYSTEMS
1 3/8 in
[34.9 mm]
MINIMUM
DOOR
THICKNESS
29/32 in
[22.9 mm]
1 in
[25.4 mm]
3/8 in
[9.5 mm]
MIN
3/8 - 1 in
[9.5 - 25.4 mm]
MIN - MAX
1 in
[25.4 mm]
29/32 in
[22.9 mm]
1 3/8 in
[34.9 mm]
MINIMUM
DOOR
THICKNESS
1 in
[25.4 mm]
29/32 in
[22.9 mm]
1 3/8 in
[34.9 mm]
MINIMUM
DOOR
THICKNESS
3/8 - 1 in
[9.5 - 25.4 mm]
MIN - MAX
1 in
[25.4 mm]
29/32 in
[22.9 mm]
1 3/8 in
[34.9 mm]
MINIMUM
DOOR
THICKNESS
3/8 in
[9.5 mm]
MIN
29/32 in
[22.9 mm]
1 in
[25.4 mm]
DOOR OPENINGDOOR POCKET
DOOR OPENINGWALL WHERE DOOR OPENS TO
CLOSED POSITION
OPENED POSITION OPENED POSITION
CLOSED POSITION
TYPICAL MINIMUM OVERLAP
IN POCKET: 2 in [50.8 mm]
TYPICAL MINIMUM OVERLAP OF
DOOR ON WALL: 2 in [50.8 mm]
1 in
[25.4 mm]
2 1/2 in
[63.5 mm]
1 1/4 in
[31.8 mm]
SUGGESTED MINIMUM
1/2 in [12.7 mm]
SET BACK REQUIRED
FOR THIS OPTION
1 in
[25.4 mm]
1 1/8 in
[28.7 mm]
2 in
[50.8 mm]
MIN - MAX
15/16 - 1 9/16 in
[23.8 - 39.7 mm]
1 1/8 in
[28.7 mm]
2 in
[50.8 mm]
1 in
[25.4 mm]
1 3/8 in
[34.9 mm]
4 in
[101.6 mm]
29/32 in
[22.9 mm]
HIGH RECESSED
IN DOOR
1 in
[25.4 mm]
WIDE RECESSED
IN DOOR
Ø 3/4 in
[19.1 mm]
Ø 3/4 in
[19.1 mm]
DOOR OPENINGDOOR POCKET
OPENED POSITION
DOOR OPENINGWALL WHERE DOOR OPENS TO
OPENED POSITION
CLOSED POSITION
TYPICAL MINIMUM OVERLAP
IN POCKET: 2 in [50.8 mm]
DOOR OPENINGDOOR POCKET
CLOSED POSITION
TYPICAL MINIMUM OVERLAP OF
DOOR ON WALL: 2 in [50.8 mm]
DOOR OPENINGWALL WHERE DOOR OPENS TO
#10 X 1-3/4”
FLAT HEAD
SCREWS
(2 SUPPLIED
PER C-913 GUIDE)
1 3/8 in
[34.9 mm]
MINIMUM
DOOR
THICKNESS
29/32 in
[22.9 mm]
1 in
[25.4 mm]
3/8 in
[9.5 mm]
MIN
3/8 - 1 in
[9.5 - 25.4 mm]
MIN - MAX
1 in
[25.4 mm]
29/32 in
[22.9 mm]
1 3/8 in
[34.9 mm]
MINIMUM
DOOR
THICKNESS
1 in
[25.4 mm]
29/32 in
[22.9 mm]
1 3/8 in
[34.9 mm]
MINIMUM
DOOR
THICKNESS
3/8 - 1 in
[9.5 - 25.4 mm]
MIN - MAX
1 in
[25.4 mm]
29/32 in
[22.9 mm]
1 3/8 in
[34.9 mm]
MINIMUM
DOOR
THICKNESS
3/8 in
[9.5 mm]
MIN
29/32 in
[22.9 mm]
1 in
[25.4 mm]
DOOR OPENINGDOOR POCKET
DOOR OPENINGWALL WHERE DOOR OPENS TO
CLOSED POSITION
OPENED POSITION OPENED POSITION
CLOSED POSITION
TYPICAL MINIMUM OVERLAP
IN POCKET: 2 in [50.8 mm]
TYPICAL MINIMUM OVERLAP OF
DOOR ON WALL: 2 in [50.8 mm]
1 in
[25.4 mm]
2 1/2 in
[63.5 mm]
1 1/4 in
[31.8 mm]
SUGGESTED MINIMUM
1/2 in [12.7 mm]
SET BACK REQUIRED
FOR THIS OPTION
1 in
[25.4 mm]
1 1/8 in
[28.7 mm]
2 in
[50.8 mm]
MIN - MAX
15/16 - 1 9/16 in
[23.8 - 39.7 mm]
1 1/8 in
[28.7 mm]
2 in
[50.8 mm]
1 in
[25.4 mm]
1 3/8 in
[34.9 mm]
4 in
[101.6 mm]
29/32 in
[22.9 mm]
HIGH RECESSED
IN DOOR
1 in
[25.4 mm]
WIDE RECESSED
IN DOOR
Ø 3/4 in
[19.1 mm]
Ø 3/4 in
[19.1 mm]
DOOR OPENINGDOOR POCKET
OPENED POSITION
DOOR OPENINGWALL WHERE DOOR OPENS TO
OPENED POSITION
CLOSED POSITION
TYPICAL MINIMUM OVERLAP
IN POCKET: 2 in [50.8 mm]
DOOR OPENINGDOOR POCKET
CLOSED POSITION
TYPICAL MINIMUM OVERLAP OF
DOOR ON WALL: 2 in [50.8 mm]
DOOR OPENINGWALL WHERE DOOR OPENS TO
#10 X 1-3/4”
FLAT HEAD
SCREWS
(4 SUPPLIED
PER C-913-2 DOUBLE
ROLLER GUIDE)
1 3/8 in
[34.9 mm]
MINIMUM
DOOR
THICKNESS
29/32 in
[22.9 mm]
1 in
[25.4 mm]
3/8 in
[9.5 mm]
MIN
3/8 - 1 in
[9.5 - 25.4 mm]
MIN - MAX
1 in
[25.4 mm]
29/32 in
[22.9 mm]
1 3/8 in
[34.9 mm]
MINIMUM
DOOR
THICKNESS
1 in
[25.4 mm]
29/32 in
[22.9 mm]
1 3/8 in
[34.9 mm]
MINIMUM
DOOR
THICKNESS
3/8 - 1 in
[9.5 - 25.4 mm]
MIN - MAX
1 in
[25.4 mm]
29/32 in
[22.9 mm]
1 3/8 in
[34.9 mm]
MINIMUM
DOOR
THICKNESS
3/8 in
[9.5 mm]
MIN
29/32 in
[22.9 mm]
1 in
[25.4 mm]
DOOR OPENINGDOOR POCKET
DOOR OPENINGWALL WHERE DOOR OPENS TO
CLOSED POSITION
OPENED POSITION OPENED POSITION
CLOSED POSITION
TYPICAL MINIMUM OVERLAP
IN POCKET: 2 in [50.8 mm]
TYPICAL MINIMUM OVERLAP OF
DOOR ON WALL: 2 in [50.8 mm]
1 in
[25.4 mm]
2 1/2 in
[63.5 mm]
1 1/4 in
[31.8 mm]
SUGGESTED MINIMUM
1/2 in [12.7 mm]
SET BACK REQUIRED
FOR THIS OPTION
1 in
[25.4 mm]
1 1/8 in
[28.7 mm]
2 in
[50.8 mm]
MIN - MAX
15/16 - 1 9/16 in
[23.8 - 39.7 mm]
1 1/8 in
[28.7 mm]
2 in
[50.8 mm]
1 in
[25.4 mm]
1 3/8 in
[34.9 mm]
4 in
[101.6 mm]
29/32 in
[22.9 mm]
HIGH RECESSED
IN DOOR
1 in
[25.4 mm]
WIDE RECESSED
IN DOOR
Ø 3/4 in
[19.1 mm]
Ø 3/4 in
[19.1 mm]
DOOR OPENINGDOOR POCKET
OPENED POSITION
DOOR OPENINGWALL WHERE DOOR OPENS TO
OPENED POSITION
CLOSED POSITION
TYPICAL MINIMUM OVERLAP
IN POCKET: 2 in [50.8 mm]
DOOR OPENINGDOOR POCKET
CLOSED POSITION
TYPICAL MINIMUM OVERLAP OF
DOOR ON WALL: 2 in [50.8 mm]
DOOR OPENINGWALL WHERE DOOR OPENS TO
C-913 GUIDE
1 3/8 in
[34.9 mm]
MINIMUM
DOOR
THICKNESS
29/32 in
[22.9 mm]
1 in
[25.4 mm]
3/8 in
[9.5 mm]
MIN
3/8 - 1 in
[9.5 - 25.4 mm]
MIN - MAX
1 in
[25.4 mm]
29/32 in
[22.9 mm]
1 3/8 in
[34.9 mm]
MINIMUM
DOOR
THICKNESS
1 in
[25.4 mm]
29/32 in
[22.9 mm]
1 3/8 in
[34.9 mm]
MINIMUM
DOOR
THICKNESS
3/8 - 1 in
[9.5 - 25.4 mm]
MIN - MAX
1 in
[25.4 mm]
29/32 in
[22.9 mm]
1 3/8 in
[34.9 mm]
MINIMUM
DOOR
THICKNESS
3/8 in
[9.5 mm]
MIN
29/32 in
[22.9 mm]
1 in
[25.4 mm]
DOOR OPENINGDOOR POCKET
DOOR OPENINGWALL WHERE DOOR OPENS TO
CLOSED POSITION
OPENED POSITION OPENED POSITION
CLOSED POSITION
TYPICAL MINIMUM OVERLAP
IN POCKET: 2 in [50.8 mm]
TYPICAL MINIMUM OVERLAP OF
DOOR ON WALL: 2 in [50.8 mm]
1 in
[25.4 mm]
2 1/2 in
[63.5 mm]
1 1/4 in
[31.8 mm]
SUGGESTED MINIMUM
1/2 in [12.7 mm]
SET BACK REQUIRED
FOR THIS OPTION
1 in
[25.4 mm]
1 1/8 in
[28.7 mm]
2 in
[50.8 mm]
MIN - MAX
15/16 - 1 9/16 in
[23.8 - 39.7 mm]
1 1/8 in
[28.7 mm]
2 in
[50.8 mm]
1 in
[25.4 mm]
1 3/8 in
[34.9 mm]
4 in
[101.6 mm]
29/32 in
[22.9 mm]
HIGH RECESSED
IN DOOR
1 in
[25.4 mm]
WIDE RECESSED
IN DOOR
Ø 3/4 in
[19.1 mm]
Ø 3/4 in
[19.1 mm]
DOOR OPENINGDOOR POCKET
OPENED POSITION
DOOR OPENINGWALL WHERE DOOR OPENS TO
OPENED POSITION
CLOSED POSITION
TYPICAL MINIMUM OVERLAP
IN POCKET: 2 in [50.8 mm]
DOOR OPENINGDOOR POCKET
CLOSED POSITION
TYPICAL MINIMUM OVERLAP OF
DOOR ON WALL: 2 in [50.8 mm]
DOOR OPENINGWALL WHERE DOOR OPENS TO
C-913-2 DOUBLE ROLLER GUIDE
1 3/8 in
[34.9 mm]
MINIMUM
DOOR
THICKNESS
29/32 in
[22.9 mm]
1 in
[25.4 mm]
3/8 in
[9.5 mm]
MIN
3/8 - 1 in
[9.5 - 25.4 mm]
MIN - MAX
1 in
[25.4 mm]
29/32 in
[22.9 mm]
1 3/8 in
[34.9 mm]
MINIMUM
DOOR
THICKNESS
1 in
[25.4 mm]
29/32 in
[22.9 mm]
1 3/8 in
[34.9 mm]
MINIMUM
DOOR
THICKNESS
3/8 - 1 in
[9.5 - 25.4 mm]
MIN - MAX
1 in
[25.4 mm]
29/32 in
[22.9 mm]
1 3/8 in
[34.9 mm]
MINIMUM
DOOR
THICKNESS
3/8 in
[9.5 mm]
MIN
29/32 in
[22.9 mm]
1 in
[25.4 mm]
DOOR OPENINGDOOR POCKET
DOOR OPENINGWALL WHERE DOOR OPENS TO
CLOSED POSITION
OPENED POSITION OPENED POSITION
CLOSED POSITION
TYPICAL MINIMUM OVERLAP
IN POCKET: 2 in [50.8 mm]
TYPICAL MINIMUM OVERLAP OF
DOOR ON WALL: 2 in [50.8 mm]
1 in
[25.4 mm]
2 1/2 in
[63.5 mm]
1 1/4 in
[31.8 mm]
SUGGESTED MINIMUM
1/2 in [12.7 mm]
SET BACK REQUIRED
FOR THIS OPTION
1 in
[25.4 mm]
1 1/8 in
[28.7 mm]
2 in
[50.8 mm]
MIN - MAX
15/16 - 1 9/16 in
[23.8 - 39.7 mm]
1 1/8 in
[28.7 mm]
2 in
[50.8 mm]
1 in
[25.4 mm]
1 3/8 in
[34.9 mm]
4 in
[101.6 mm]
29/32 in
[22.9 mm]
HIGH RECESSED
IN DOOR
1 in
[25.4 mm]
WIDE RECESSED
IN DOOR
Ø 3/4 in
[19.1 mm]
Ø 3/4 in
[19.1 mm]
DOOR OPENINGDOOR POCKET
OPENED POSITION
DOOR OPENINGWALL WHERE DOOR OPENS TO
OPENED POSITION
CLOSED POSITION
TYPICAL MINIMUM OVERLAP
IN POCKET: 2 in [50.8 mm]
DOOR OPENINGDOOR POCKET
CLOSED POSITION
TYPICAL MINIMUM OVERLAP OF
DOOR ON WALL: 2 in [50.8 mm]
DOOR OPENINGWALL WHERE DOOR OPENS TO
C-914 GUIDE CHANNEL X LENGTH
(FOR GUIDE CHANNEL RECESSED INTO BOTTOM OF DOOR, LENGTH = DOOR WIDTH,
EXAMPLE: 36” [914MM] DOOR = 36” [914MM] GUIDE CHANNEL)
(FOR GUIDE CHANNEL MOUNTED IN FLOOR, LENGTH = OPENING WIDTH + POCKET
IF APPLICABLE, EXAMPLE: TWO 36” [914 MM] DOORS IN A BY-PASSING APPLICATION WILL
REQUIRED TWO 72” [1828 MM] LONG GUIDE CHANNELS TO FILL OPENING.
TYPICAL INSTALLATION LOCATION FOR FLOOR GUIDES: POCKET DOOR APPLICATION
GUIDE CHANNEL IN DOOR WITH GUIDE ON FLOOR FOR POCKET DOOR APPLICATIONS ILLUSTRATED BELOW:
1 3/8 in
[34.9 mm]
MINIMUM
DOOR
THICKNESS
29/32 in
[22.9 mm]
1 in
[25.4 mm]
3/8 in
[9.5 mm]
MIN
3/8 - 1 in
[9.5 - 25.4 mm]
MIN - MAX
1 in
[25.4 mm]
29/32 in
[22.9 mm]
1 3/8 in
[34.9 mm]
MINIMUM
DOOR
THICKNESS
1 in
[25.4 mm]
29/32 in
[22.9 mm]
1 3/8 in
[34.9 mm]
MINIMUM
DOOR
THICKNESS
3/8 - 1 in
[9.5 - 25.4 mm]
MIN - MAX
1 in
[25.4 mm]
29/32 in
[22.9 mm]
1 3/8 in
[34.9 mm]
MINIMUM
DOOR
THICKNESS
3/8 in
[9.5 mm]
MIN
29/32 in
[22.9 mm]
1 in
[25.4 mm]
DOOR OPENINGDOOR POCKET
DOOR OPENINGWALL WHERE DOOR OPENS TO
CLOSED POSITION
OPENED POSITION OPENED POSITION
CLOSED POSITION
TYPICAL MINIMUM OVERLAP
IN POCKET: 2 in [50.8 mm]
TYPICAL MINIMUM OVERLAP OF
DOOR ON WALL: 2 in [50.8 mm]
1 in
[25.4 mm]
2 1/2 in
[63.5 mm]
1 1/4 in
[31.8 mm]
SUGGESTED MINIMUM
1/2 in [12.7 mm]
SET BACK REQUIRED
FOR THIS OPTION
1 in
[25.4 mm]
1 1/8 in
[28.7 mm]
2 in
[50.8 mm]
MIN - MAX
15/16 - 1 9/16 in
[23.8 - 39.7 mm]
1 1/8 in
[28.7 mm]
2 in
[50.8 mm]
1 in
[25.4 mm]
1 3/8 in
[34.9 mm]
4 in
[101.6 mm]
29/32 in
[22.9 mm]
HIGH RECESSED
IN DOOR
1 in
[25.4 mm]
WIDE RECESSED
IN DOOR
Ø 3/4 in
[19.1 mm]
Ø 3/4 in
[19.1 mm]
DOOR OPENINGDOOR POCKET
OPENED POSITION
DOOR OPENINGWALL WHERE DOOR OPENS TO
OPENED POSITION
CLOSED POSITION
TYPICAL MINIMUM OVERLAP
IN POCKET: 2 in [50.8 mm]
DOOR OPENINGDOOR POCKET
CLOSED POSITION
TYPICAL MINIMUM OVERLAP OF
DOOR ON WALL: 2 in [50.8 mm]
DOOR OPENINGWALL WHERE DOOR OPENS TO
1 3/8 in
[34.9 mm]
MINIMUM
DOOR
THICKNESS
29/32 in
[22.9 mm]
1 in
[25.4 mm]
3/8 in
[9.5 mm]
MIN
3/8 - 1 in
[9.5 - 25.4 mm]
MIN - MAX
1 in
[25.4 mm]
29/32 in
[22.9 mm]
1 3/8 in
[34.9 mm]
MINIMUM
DOOR
THICKNESS
1 in
[25.4 mm]
29/32 in
[22.9 mm]
1 3/8 in
[34.9 mm]
MINIMUM
DOOR
THICKNESS
3/8 - 1 in
[9.5 - 25.4 mm]
MIN - MAX
1 in
[25.4 mm]
29/32 in
[22.9 mm]
1 3/8 in
[34.9 mm]
MINIMUM
DOOR
THICKNESS
3/8 in
[9.5 mm]
MIN
29/32 in
[22.9 mm]
1 in
[25.4 mm]
DOOR OPENINGDOOR POCKET
DOOR OPENINGWALL WHERE DOOR OPENS TO
CLOSED POSITION
OPENED POSITION OPENED POSITION
CLOSED POSITION
TYPICAL MINIMUM OVERLAP
IN POCKET: 2 in [50.8 mm]
TYPICAL MINIMUM OVERLAP OF
DOOR ON WALL: 2 in [50.8 mm]
1 in
[25.4 mm]
2 1/2 in
[63.5 mm]
1 1/4 in
[31.8 mm]
SUGGESTED MINIMUM
1/2 in [12.7 mm]
SET BACK REQUIRED
FOR THIS OPTION
1 in
[25.4 mm]
1 1/8 in
[28.7 mm]
2 in
[50.8 mm]
MIN - MAX
15/16 - 1 9/16 in
[23.8 - 39.7 mm]
1 1/8 in
[28.7 mm]
2 in
[50.8 mm]
1 in
[25.4 mm]
1 3/8 in
[34.9 mm]
4 in
[101.6 mm]
29/32 in
[22.9 mm]
HIGH RECESSED
IN DOOR
1 in
[25.4 mm]
WIDE RECESSED
IN DOOR
Ø 3/4 in
[19.1 mm]
Ø 3/4 in
[19.1 mm]
DOOR OPENINGDOOR POCKET
OPENED POSITION
DOOR OPENINGWALL WHERE DOOR OPENS TO
OPENED POSITION
CLOSED POSITION
TYPICAL MINIMUM OVERLAP
IN POCKET: 2 in [50.8 mm]
DOOR OPENING
DOOR POCKET
CLOSED POSITION
TYPICAL MINIMUM OVERLAP OF
DOOR ON WALL: 2 in [50.8 mm]
DOOR OPENINGWALL WHERE DOOR OPENS TO
TYPICAL INSTALLATION LOCATION FOR FLOOR GUIDES: BARN DOOR APPLICATION
GUIDE CHANNEL IN DOOR WITH GUIDE ON FLOOR FOR BARN DOOR APPLICATIONS ILLUSTRATED BELOW:
1 3/8 in
[34.9 mm]
MINIMUM
DOOR
THICKNESS
29/32 in
[22.9 mm]
1 in
[25.4 mm]
3/8 in
[9.5 mm]
MIN
3/8 - 1 in
[9.5 - 25.4 mm]
MIN - MAX
1 in
[25.4 mm]
29/32 in
[22.9 mm]
1 3/8 in
[34.9 mm]
MINIMUM
DOOR
THICKNESS
1 in
[25.4 mm]
29/32 in
[22.9 mm]
1 3/8 in
[34.9 mm]
MINIMUM
DOOR
THICKNESS
3/8 - 1 in
[9.5 - 25.4 mm]
MIN - MAX
1 in
[25.4 mm]
29/32 in
[22.9 mm]
1 3/8 in
[34.9 mm]
MINIMUM
DOOR
THICKNESS
3/8 in
[9.5 mm]
MIN
29/32 in
[22.9 mm]
1 in
[25.4 mm]
DOOR OPENINGDOOR POCKET
DOOR OPENINGWALL WHERE DOOR OPENS TO
CLOSED POSITION
OPENED POSITION OPENED POSITION
CLOSED POSITION
TYPICAL MINIMUM OVERLAP
IN POCKET: 2 in [50.8 mm]
TYPICAL MINIMUM OVERLAP OF
DOOR ON WALL: 2 in [50.8 mm]
1 in
[25.4 mm]
2 1/2 in
[63.5 mm]
1 1/4 in
[31.8 mm]
SUGGESTED MINIMUM
1/2 in [12.7 mm]
SET BACK REQUIRED
FOR THIS OPTION
1 in
[25.4 mm]
1 1/8 in
[28.7 mm]
2 in
[50.8 mm]
MIN - MAX
15/16 - 1 9/16 in
[23.8 - 39.7 mm]
1 1/8 in
[28.7 mm]
2 in
[50.8 mm]
1 in
[25.4 mm]
1 3/8 in
[34.9 mm]
4 in
[101.6 mm]
29/32 in
[22.9 mm]
HIGH RECESSED
IN DOOR
1 in
[25.4 mm]
WIDE RECESSED
IN DOOR
Ø 3/4 in
[19.1 mm]
Ø 3/4 in
[19.1 mm]
DOOR OPENINGDOOR POCKET
OPENED POSITION
DOOR OPENINGWALL WHERE DOOR OPENS TO
OPENED POSITION
CLOSED POSITION
TYPICAL MINIMUM OVERLAP
IN POCKET: 2 in [50.8 mm]
DOOR OPENINGDOOR POCKET
CLOSED POSITION
TYPICAL MINIMUM OVERLAP OF
DOOR ON WALL: 2 in [50.8 mm]
DOOR OPENINGWALL WHERE DOOR OPENS TO
1 3/8 in
[34.9 mm]
MINIMUM
DOOR
THICKNESS
29/32 in
[22.9 mm]
1 in
[25.4 mm]
3/8 in
[9.5 mm]
MIN
3/8 - 1 in
[9.5 - 25.4 mm]
MIN - MAX
1 in
[25.4 mm]
29/32 in
[22.9 mm]
1 3/8 in
[34.9 mm]
MINIMUM
DOOR
THICKNESS
1 in
[25.4 mm]
29/32 in
[22.9 mm]
1 3/8 in
[34.9 mm]
MINIMUM
DOOR
THICKNESS
3/8 - 1 in
[9.5 - 25.4 mm]
MIN - MAX
1 in
[25.4 mm]
29/32 in
[22.9 mm]
1 3/8 in
[34.9 mm]
MINIMUM
DOOR
THICKNESS
3/8 in
[9.5 mm]
MIN
29/32 in
[22.9 mm]
1 in
[25.4 mm]
DOOR OPENINGDOOR POCKET
DOOR OPENINGWALL WHERE DOOR OPENS TO
CLOSED POSITION
OPENED POSITION OPENED POSITION
CLOSED POSITION
TYPICAL MINIMUM OVERLAP
IN POCKET: 2 in [50.8 mm]
TYPICAL MINIMUM OVERLAP OF
DOOR ON WALL: 2 in [50.8 mm]
1 in
[25.4 mm]
2 1/2 in
[63.5 mm]
1 1/4 in
[31.8 mm]
SUGGESTED MINIMUM
1/2 in [12.7 mm]
SET BACK REQUIRED
FOR THIS OPTION
1 in
[25.4 mm]
1 1/8 in
[28.7 mm]
2 in
[50.8 mm]
MIN - MAX
15/16 - 1 9/16 in
[23.8 - 39.7 mm]
1 1/8 in
[28.7 mm]
2 in
[50.8 mm]
1 in
[25.4 mm]
1 3/8 in
[34.9 mm]
4 in
[101.6 mm]
29/32 in
[22.9 mm]
HIGH RECESSED
IN DOOR
1 in
[25.4 mm]
WIDE RECESSED
IN DOOR
Ø 3/4 in
[19.1 mm]
Ø 3/4 in
[19.1 mm]
DOOR OPENINGDOOR POCKET
OPENED POSITION
DOOR OPENINGWALL WHERE DOOR OPENS TO
OPENED POSITION
CLOSED POSITION
TYPICAL MINIMUM OVERLAP
IN POCKET: 2 in [50.8 mm]
DOOR OPENINGDOOR POCKET
CLOSED POSITION
TYPICAL MINIMUM OVERLAP OF
DOOR ON WALL: 2 in [50.8 mm]
DOOR OPENINGWALL WHERE DOOR OPENS TO
NOTE: IF USING THE C-913-2 DOUBLE ROLLER GUIDE, THE TYPICAL MINIMUM OVERLAP IS 4 in [101.6 mm]
A PRODUCT OF K.N. CROWDER MFG. INC.
© 2016 K.N. CROWDER MFG. INC. All Rights Reserved. PAGE 2
1 3/8 in
[34.9 mm]
MINIMUM
DOOR
THICKNESS
29/32 in
[22.9 mm]
1 in
[25.4 mm]
3/8 in
[9.5 mm]
MIN
3/8 - 1 in
[9.5 - 25.4 mm]
MIN - MAX
1 in
[25.4 mm]
29/32 in
[22.9 mm]
1 3/8 in
[34.9 mm]
MINIMUM
DOOR
THICKNESS
1 in
[25.4 mm]
29/32 in
[22.9 mm]
1 3/8 in
[34.9 mm]
MINIMUM
DOOR
THICKNESS
3/8 - 1 in
[9.5 - 25.4 mm]
MIN - MAX
1 in
[25.4 mm]
29/32 in
[22.9 mm]
1 3/8 in
[34.9 mm]
MINIMUM
DOOR
THICKNESS
3/8 in
[9.5 mm]
MIN
29/32 in
[22.9 mm]
1 in
[25.4 mm]
DOOR OPENINGDOOR POCKET
DOOR OPENINGWALL WHERE DOOR OPENS TO
CLOSED POSITION
OPENED POSITION OPENED POSITION
CLOSED POSITION
TYPICAL MINIMUM OVERLAP
IN POCKET: 2 in [50.8 mm]
TYPICAL MINIMUM OVERLAP OF
DOOR ON WALL: 2 in [50.8 mm]
1 in
[25.4 mm]
2 1/2 in
[63.5 mm]
1 1/4 in
[31.8 mm]
SUGGESTED MINIMUM
1/2 in [12.7 mm]
SET BACK REQUIRED
FOR THIS OPTION
1 in
[25.4 mm]
1 1/8 in
[28.7 mm]
2 in
[50.8 mm]
MIN - MAX
15/16 - 1 9/16 in
[23.8 - 39.7 mm]
1 1/8 in
[28.7 mm]
2 in
[50.8 mm]
1 in
[25.4 mm]
1 3/8 in
[34.9 mm]
4 in
[101.6 mm]
29/32 in
[22.9 mm]
HIGH RECESSED
IN DOOR
1 in
[25.4 mm]
WIDE RECESSED
IN DOOR
Ø 3/4 in
[19.1 mm]
Ø 3/4 in
[19.1 mm]
DOOR OPENINGDOOR POCKET
OPENED POSITION
DOOR OPENINGWALL WHERE DOOR OPENS TO
OPENED POSITION
CLOSED POSITION
TYPICAL MINIMUM OVERLAP
IN POCKET: 2 in [50.8 mm]
DOOR OPENINGDOOR POCKET
CLOSED POSITION
TYPICAL MINIMUM OVERLAP OF
DOOR ON WALL: 2 in [50.8 mm]
DOOR OPENINGWALL WHERE DOOR OPENS TO
STEP #2
CUT C-914 ALUMINUM GUIDE CHANNEL TO CORRECT LENGTH AS
REQUIRED. DRILL HOLES IN C-914 GUIDE CHANNEL AND
PRE-DRILL HOLES IN DOOR. LOCATE CHANNEL IN SLOT PREVIOUSLY
PREPARED ABOVE AND SCREW CHANNEL INTO PLACE WITH
RECOMMENDED #8 X 3/4” PAN HEAD SCREWS (BY OTHERS).
GUIDE SYSTEM INSTALLATION OPTION #1:
GUIDE CHANNEL IN DOOR WITH GUIDE ON FLOOR
STEP #1 CONT’D
PREPARE C-914 GUIDE CHANNEL SLOT IN DOOR AT LEAST 1 in [25.4
mm] WIDE IN CENTER OF DOOR, AND AT LEAST 29/32 in [23 mm]
DEEP. IT IS RECOMMENDED TO MAKE THE SLOT AS ACCURATE AS
POSSIBLE FOR SECURE FIT AND NEAT APPEARANCE. SEE BELOW:
STEP #1:
PREPARE BOTTOM OF DOOR ACCORDINGLY.
AESTHETIC NOTE: IF SUFFICIENT OVERLAP OF THE DOOR IS
PROVIDED, GUIDE CHANNEL CAN BE RECESSED INTO THE DOOR
WITHOUT CUTTING A SLOT THE FULL LENGTH OF THE DOOR. IF
GUIDE CHANNEL WILL BE INSTALLED SHORT FROM THE EDGES,
IT IS RECOMMENDED TO HAVE AT LEAST 1/2 in [12.7 mm] DOOR
MATERIAL AT EACH END OF THE DOOR BEFORE THE START OF
THE GUIDE CHANNEL SLOT.
DOOR OPENINGDOOR POCKET
DOOR OPENINGWALL WHERE DOOR OPENS TO
CLOSED POSITION
OPENED POSITION OPENED POSITION
CLOSED POSITION
5/8 in
[15.9 mm]
WIDE RECESSED
IN DOOR
3/4 in
[19.1 mm]
HIGH RECESSED
IN DOOR
29/32 in
[22.9 mm]
HIGH RECESSED
IN DOOR
1 in
[25.4 mm]
WIDE RECESSED
IN DOOR
13/32 in
[10.3 mm]
WIDE RECESSED
IN DOOR
***CHECK FIT
WITH GUIDE***
3/4 in
[19.1 mm]
HIGH RECESSED
IN DOOR
TYPICAL MINIMUM OVERLAP
IN POCKET: 2 in [50.8 mm]
TYPICAL MINIMUM OVERLAP OF
DOOR ON WALL: 2 in [50.8 mm]
3/4 in
[19.1 mm]
2 in
[50.8 mm]
5/8 in
[15.9 mm]
SUGGESTED MINIMUM
1/2 in [12.7 mm]
SET BACK REQUIRED
FOR THIS OPTION
DOOR OPENINGWALL WHERE DOOR OPENS TO
OPENED POSITION
CLOSED POSITION
TYPICAL MINIMUM OVERLAP OF
DOOR ON WALL: 2 in [50.8 mm]
1 in
[25.4 mm]
1 1/8 in
[28.7 mm]
2 in
[50.8 mm]
1 3/8 in
[34.9 mm]
MINIMUM
DOOR
THICKNESS
29/32 in
[22.9 mm]
1 in
[25.4 mm]
3/8 in
[9.5 mm]
MIN
3/8 - 1 in
[9.5 - 25.4 mm]
MIN - MAX
1 in
[25.4 mm]
29/32 in
[22.9 mm]
1 3/8 in
[34.9 mm]
MINIMUM
DOOR
THICKNESS
1 in
[25.4 mm]
29/32 in
[22.9 mm]
1 3/8 in
[34.9 mm]
MINIMUM
DOOR
THICKNESS
3/8 - 1 in
[9.5 - 25.4 mm]
MIN - MAX
1 in
[25.4 mm]
29/32 in
[22.9 mm]
1 3/8 in
[34.9 mm]
MINIMUM
DOOR
THICKNESS
3/8 in
[9.5 mm]
MIN
29/32 in
[22.9 mm]
1 in
[25.4 mm]
DOOR OPENINGDOOR POCKET
DOOR OPENINGWALL WHERE DOOR OPENS TO
CLOSED POSITION
OPENED POSITION OPENED POSITION
CLOSED POSITION
TYPICAL MINIMUM OVERLAP
IN POCKET: 2 in [50.8 mm]
TYPICAL MINIMUM OVERLAP OF
DOOR ON WALL: 2 in [50.8 mm]
1 in
[25.4 mm]
2 1/2 in
[63.5 mm]
1 1/4 in
[31.8 mm]
SUGGESTED MINIMUM
1/2 in [12.7 mm]
SET BACK REQUIRED
FOR THIS OPTION
1 in
[25.4 mm]
1 1/8 in
[28.7 mm]
2 in
[50.8 mm]
MIN - MAX
15/16 - 1 9/16 in
[23.8 - 39.7 mm]
1 1/8 in
[28.7 mm]
2 in
[50.8 mm]
1 in
[25.4 mm]
1 3/8 in
[34.9 mm]
4 in
[101.6 mm]
29/32 in
[22.9 mm]
HIGH RECESSED
IN DOOR
1 in
[25.4 mm]
WIDE RECESSED
IN DOOR
Ø 3/4 in
[19.1 mm]
Ø 3/4 in
[19.1 mm]
DOOR OPENINGDOOR POCKET
OPENED POSITION
DOOR OPENINGWALL WHERE DOOR OPENS TO
OPENED POSITION
CLOSED POSITION
TYPICAL MINIMUM OVERLAP
IN POCKET: 2 in [50.8 mm]
DOOR OPENINGDOOR POCKET
CLOSED POSITION
TYPICAL MINIMUM OVERLAP OF
DOOR ON WALL: 2 in [50.8 mm]
DOOR OPENINGWALL WHERE DOOR OPENS TO
STEP #3
LOCATE C-913 GUIDE AS PER
REQUIREMENT BASED ON
THE SUGGESTIONS FOUND
ON OPPOSITE SIDE AND SITE
CONDITIONS AND SECURE TO
FLOOR WITH #10 X 1-3/4” FLAT
HEAD SCREWS (2).
OR
LOCATE C-913-2 DOUBLE
ROLLER GUIDE AS PER
REQUIREMENT BASED ON
THE SUGGESTIONS FOUND
ON OPPOSITE SIDE AND SITE
CONDITIONS AND SECURE TO
FLOOR WITH #10 X 1-3/4” FLAT
HEAD SCREWS (4).
STEP #4
CONTINUE WITH PROJECT BY
INSTALLING HANGERS AND
PLACING DOOR INTO
POSITION AS REQUIRED.
1 3/8 in
[34.9 mm]
MINIMUM
DOOR
THICKNESS
29/32 in
[22.9 mm]
1 in
[25.4 mm]
3/8 in
[9.5 mm]
MIN
3/8 - 1 in
[9.5 - 25.4 mm]
MIN - MAX
1 in
[25.4 mm]
29/32 in
[22.9 mm]
1 3/8 in
[34.9 mm]
MINIMUM
DOOR
THICKNESS
1 in
[25.4 mm]
29/32 in
[22.9 mm]
1 3/8 in
[34.9 mm]
MINIMUM
DOOR
THICKNESS
3/8 - 1 in
[9.5 - 25.4 mm]
MIN - MAX
1 in
[25.4 mm]
29/32 in
[22.9 mm]
1 3/8 in
[34.9 mm]
MINIMUM
DOOR
THICKNESS
3/8 in
[9.5 mm]
MIN
29/32 in
[22.9 mm]
1 in
[25.4 mm]
DOOR OPENINGDOOR POCKET
DOOR OPENINGWALL WHERE DOOR OPENS TO
CLOSED POSITION
OPENED POSITION OPENED POSITION
CLOSED POSITION
TYPICAL MINIMUM OVERLAP
IN POCKET: 2 in [50.8 mm]
TYPICAL MINIMUM OVERLAP OF
DOOR ON WALL: 2 in [50.8 mm]
1 in
[25.4 mm]
2 1/2 in
[63.5 mm]
1 1/4 in
[31.8 mm]
SUGGESTED MINIMUM
1/2 in [12.7 mm]
SET BACK REQUIRED
FOR THIS OPTION
1 in
[25.4 mm]
1 1/8 in
[28.7 mm]
2 in
[50.8 mm]
MIN - MAX
15/16 - 1 9/16 in
[23.8 - 39.7 mm]
1 1/8 in
[28.7 mm]
2 in
[50.8 mm]
1 in
[25.4 mm]
1 3/8 in
[34.9 mm]
4 in
[101.6 mm]
29/32 in
[22.9 mm]
HIGH RECESSED
IN DOOR
1 in
[25.4 mm]
WIDE RECESSED
IN DOOR
Ø 3/4 in
[19.1 mm]
Ø 3/4 in
[19.1 mm]
DOOR OPENINGDOOR POCKET
OPENED POSITION
DOOR OPENINGWALL WHERE DOOR OPENS TO
OPENED POSITION
CLOSED POSITION
TYPICAL MINIMUM OVERLAP
IN POCKET: 2 in [50.8 mm]
DOOR OPENINGDOOR POCKET
CLOSED POSITION
TYPICAL MINIMUM OVERLAP OF
DOOR ON WALL: 2 in [50.8 mm]
DOOR OPENINGWALL WHERE DOOR OPENS TO
EXAMPLE OF FINISHED SET-UP
SHOWN WITH DOOR
1 3/8 in
[34.9 mm]
MINIMUM
DOOR
THICKNESS
29/32 in
[22.9 mm]
1 in
[25.4 mm]
3/8 in
[9.5 mm]
MIN
3/8 - 1 in
[9.5 - 25.4 mm]
MIN - MAX
1 in
[25.4 mm]
29/32 in
[22.9 mm]
1 3/8 in
[34.9 mm]
MINIMUM
DOOR
THICKNESS
1 in
[25.4 mm]
29/32 in
[22.9 mm]
1 3/8 in
[34.9 mm]
MINIMUM
DOOR
THICKNESS
3/8 - 1 in
[9.5 - 25.4 mm]
MIN - MAX
1 in
[25.4 mm]
29/32 in
[22.9 mm]
1 3/8 in
[34.9 mm]
MINIMUM
DOOR
THICKNESS
3/8 in
[9.5 mm]
MIN
29/32 in
[22.9 mm]
1 in
[25.4 mm]
DOOR OPENINGDOOR POCKET
DOOR OPENINGWALL WHERE DOOR OPENS TO
CLOSED POSITION
OPENED POSITION OPENED POSITION
CLOSED POSITION
TYPICAL MINIMUM OVERLAP
IN POCKET: 2 in [50.8 mm]
TYPICAL MINIMUM OVERLAP OF
DOOR ON WALL: 2 in [50.8 mm]
1 in
[25.4 mm]
2 1/2 in
[63.5 mm]
1 1/4 in
[31.8 mm]
SUGGESTED MINIMUM
1/2 in [12.7 mm]
SET BACK REQUIRED
FOR THIS OPTION
1 in
[25.4 mm]
1 1/8 in
[28.7 mm]
2 in
[50.8 mm]
MIN - MAX
15/16 - 1 9/16 in
[23.8 - 39.7 mm]
1 1/8 in
[28.7 mm]
2 in
[50.8 mm]
1 in
[25.4 mm]
1 3/8 in
[34.9 mm]
4 in
[101.6 mm]
29/32 in
[22.9 mm]
HIGH RECESSED
IN DOOR
1 in
[25.4 mm]
WIDE RECESSED
IN DOOR
Ø 3/4 in
[19.1 mm]
Ø 3/4 in
[19.1 mm]
DOOR OPENINGDOOR POCKET
OPENED POSITION
DOOR OPENINGWALL WHERE DOOR OPENS TO
OPENED POSITION
CLOSED POSITION
TYPICAL MINIMUM OVERLAP
IN POCKET: 2 in [50.8 mm]
DOOR OPENINGDOOR POCKET
CLOSED POSITION
TYPICAL MINIMUM OVERLAP OF
DOOR ON WALL: 2 in [50.8 mm]
DOOR OPENINGWALL WHERE DOOR OPENS TO
1 3/8 in
[34.9 mm]
MINIMUM
DOOR
THICKNESS
29/32 in
[22.9 mm]
1 in
[25.4 mm]
3/8 in
[9.5 mm]
MIN
3/8 - 1 in
[9.5 - 25.4 mm]
MIN - MAX
1 in
[25.4 mm]
29/32 in
[22.9 mm]
1 3/8 in
[34.9 mm]
MINIMUM
DOOR
THICKNESS
1 in
[25.4 mm]
29/32 in
[22.9 mm]
1 3/8 in
[34.9 mm]
MINIMUM
DOOR
THICKNESS
3/8 - 1 in
[9.5 - 25.4 mm]
MIN - MAX
1 in
[25.4 mm]
29/32 in
[22.9 mm]
1 3/8 in
[34.9 mm]
MINIMUM
DOOR
THICKNESS
3/8 in
[9.5 mm]
MIN
29/32 in
[22.9 mm]
1 in
[25.4 mm]
DOOR OPENINGDOOR POCKET
DOOR OPENINGWALL WHERE DOOR OPENS TO
CLOSED POSITION
OPENED POSITION OPENED POSITION
CLOSED POSITION
TYPICAL MINIMUM OVERLAP
IN POCKET: 2 in [50.8 mm]
TYPICAL MINIMUM OVERLAP OF
DOOR ON WALL: 2 in [50.8 mm]
1 in
[25.4 mm]
2 1/2 in
[63.5 mm]
1 1/4 in
[31.8 mm]
SUGGESTED MINIMUM
1/2 in [12.7 mm]
SET BACK REQUIRED
FOR THIS OPTION
1 in
[25.4 mm]
1 1/8 in
[28.7 mm]
2 in
[50.8 mm]
MIN - MAX
15/16 - 1 9/16 in
[23.8 - 39.7 mm]
1 1/8 in
[28.7 mm]
2 in
[50.8 mm]
1 in
[25.4 mm]
1 3/8 in
[34.9 mm]
4 in
[101.6 mm]
29/32 in
[22.9 mm]
HIGH RECESSED
IN DOOR
1 in
[25.4 mm]
WIDE RECESSED
IN DOOR
Ø 3/4 in
[19.1 mm]
Ø 3/4 in
[19.1 mm]
DOOR OPENINGDOOR POCKET
OPENED POSITION
DOOR OPENINGWALL WHERE DOOR OPENS TO
OPENED POSITION
CLOSED POSITION
TYPICAL MINIMUM OVERLAP
IN POCKET: 2 in [50.8 mm]
DOOR OPENINGDOOR POCKET
CLOSED POSITION
TYPICAL MINIMUM OVERLAP OF
DOOR ON WALL: 2 in [50.8 mm]
DOOR OPENINGWALL WHERE DOOR OPENS TO
GUIDE SYSTEM INSTALLATION OPTION #2:
GUIDE CHANNEL IN FLOOR WITH GUIDE(S) ON DOOR
STEP #1:
PREPARE SLOT IN FLOOR FOR C-914 GUIDE CHANNEL RECESSED
IN FLOOR AS PER DIMENSION DETAILS ON OPPOSITE SIDE. GUIDE
CHANNEL SHOULD BE FLUSH WITH FINISHED FLOOR.
STEP #2:
CUT C-914 GUIDE CHANNEL TO REQUIRED
LENGTH FOR APPLICATION IF NECESSARY.
PRE-DRILL HOLES INTO THE EXTRUSION.
IT IS RECOMMENDED TO PRE-DRILL THE
FLOOR WITH A SMALLER DRILL BIT THAN
THE SCREW DIAMETER.
STEP #3:
POSITION C-914 GUIDE CHANNEL IN FLOOR SLOT AND SECURE WITH
RECOMMENDED #8 PAN HEADS OR FLAT HEAD SCREWS (BY OTHERS).
1 3/8 in
[34.9 mm]
MINIMUM
DOOR
THICKNESS
29/32 in
[22.9 mm]
1 in
[25.4 mm]
3/8 in
[9.5 mm]
MIN
3/8 - 1 in
[9.5 - 25.4 mm]
MIN - MAX
1 in
[25.4 mm]
29/32 in
[22.9 mm]
1 3/8 in
[34.9 mm]
MINIMUM
DOOR
THICKNESS
1 in
[25.4 mm]
29/32 in
[22.9 mm]
1 3/8 in
[34.9 mm]
MINIMUM
DOOR
THICKNESS
3/8 - 1 in
[9.5 - 25.4 mm]
MIN - MAX
1 in
[25.4 mm]
29/32 in
[22.9 mm]
1 3/8 in
[34.9 mm]
MINIMUM
DOOR
THICKNESS
3/8 in
[9.5 mm]
MIN
29/32 in
[22.9 mm]
1 in
[25.4 mm]
DOOR OPENINGDOOR POCKET
DOOR OPENINGWALL WHERE DOOR OPENS TO
CLOSED POSITION
OPENED POSITION OPENED POSITION
CLOSED POSITION
TYPICAL MINIMUM OVERLAP
IN POCKET: 2 in [50.8 mm]
TYPICAL MINIMUM OVERLAP OF
DOOR ON WALL: 2 in [50.8 mm]
1 in
[25.4 mm]
2 1/2 in
[63.5 mm]
1 1/4 in
[31.8 mm]
SUGGESTED MINIMUM
1/2 in [12.7 mm]
SET BACK REQUIRED
FOR THIS OPTION
1 in
[25.4 mm]
1 1/8 in
[28.7 mm]
2 in
[50.8 mm]
MIN - MAX
15/16 - 1 9/16 in
[23.8 - 39.7 mm]
1 1/8 in
[28.7 mm]
2 in
[50.8 mm]
1 in
[25.4 mm]
1 3/8 in
[34.9 mm]
4 in
[101.6 mm]
29/32 in
[22.9 mm]
HIGH RECESSED
IN DOOR
1 in
[25.4 mm]
WIDE RECESSED
IN DOOR
Ø 3/4 in
[19.1 mm]
Ø 3/4 in
[19.1 mm]
DOOR OPENINGDOOR POCKET
OPENED POSITION
DOOR OPENINGWALL WHERE DOOR OPENS TO
OPENED POSITION
CLOSED POSITION
TYPICAL MINIMUM OVERLAP
IN POCKET: 2 in [50.8 mm]
DOOR OPENINGDOOR POCKET
CLOSED POSITION
TYPICAL MINIMUM OVERLAP OF
DOOR ON WALL: 2 in [50.8 mm]
DOOR OPENINGWALL WHERE DOOR OPENS TO
STEP #4:
LOCATE C-913 GUIDE AT LEAST 2 in [50.8 mm] FROM EACH EDGE OF
THE DOOR. (IT IS RECOMMENDED TO USE TWO GUIDES PER DOOR
FOR APPLICATIONS WITH GUIDE CHANNEL RECESSED IN FLOOR).
STEP #5:
SECURE GUIDES TO DOOR WITH
#10 X 1-3/4” FLAT HEAD SCREWS (2).
IT IS RECOMMENDED TO
PRE-DRILL PILOT HOLES FOR
THE SCREWS BEFORE SECURING
GUIDES TO DOOR.
STEP #6
CONTINUE WITH PROJECT BY
INSTALLING HANGERS AND
PLACING DOOR INTO POSITION
AS REQUIRED.
EXAMPLE OF FINISHED SET-UP
SHOWN WITH DOOR
1 3/8 in
[34.9 mm]
MINIMUM
DOOR
THICKNESS
29/32 in
[22.9 mm]
1 in
[25.4 mm]
3/8 in
[9.5 mm]
MIN
3/8 - 1 in
[9.5 - 25.4 mm]
MIN - MAX
1 in
[25.4 mm]
29/32 in
[22.9 mm]
1 3/8 in
[34.9 mm]
MINIMUM
DOOR
THICKNESS
1 in
[25.4 mm]
29/32 in
[22.9 mm]
1 3/8 in
[34.9 mm]
MINIMUM
DOOR
THICKNESS
3/8 - 1 in
[9.5 - 25.4 mm]
MIN - MAX
1 in
[25.4 mm]
29/32 in
[22.9 mm]
1 3/8 in
[34.9 mm]
MINIMUM
DOOR
THICKNESS
3/8 in
[9.5 mm]
MIN
29/32 in
[22.9 mm]
1 in
[25.4 mm]
DOOR OPENINGDOOR POCKET
DOOR OPENINGWALL WHERE DOOR OPENS TO
CLOSED POSITION
OPENED POSITION OPENED POSITION
CLOSED POSITION
TYPICAL MINIMUM OVERLAP
IN POCKET: 2 in [50.8 mm]
TYPICAL MINIMUM OVERLAP OF
DOOR ON WALL: 2 in [50.8 mm]
1 in
[25.4 mm]
2 1/2 in
[63.5 mm]
1 1/4 in
[31.8 mm]
SUGGESTED MINIMUM
1/2 in [12.7 mm]
SET BACK REQUIRED
FOR THIS OPTION
1 in
[25.4 mm]
1 1/8 in
[28.7 mm]
2 in
[50.8 mm]
MIN - MAX
15/16 - 1 9/16 in
[23.8 - 39.7 mm]
1 1/8 in
[28.7 mm]
2 in
[50.8 mm]
1 in
[25.4 mm]
1 3/8 in
[34.9 mm]
4 in
[101.6 mm]
29/32 in
[22.9 mm]
HIGH RECESSED
IN DOOR
1 in
[25.4 mm]
WIDE RECESSED
IN DOOR
Ø 3/4 in
[19.1 mm]
Ø 3/4 in
[19.1 mm]
DOOR OPENINGDOOR POCKET
OPENED POSITION
DOOR OPENINGWALL WHERE DOOR OPENS TO
OPENED POSITION
CLOSED POSITION
TYPICAL MINIMUM OVERLAP
IN POCKET: 2 in [50.8 mm]
DOOR OPENINGDOOR POCKET
CLOSED POSITION
TYPICAL MINIMUM OVERLAP OF
DOOR ON WALL: 2 in [50.8 mm]
DOOR OPENINGWALL WHERE DOOR OPENS TO
1 3/8 in
[34.9 mm]
MINIMUM
DOOR
THICKNESS
29/32 in
[22.9 mm]
1 in
[25.4 mm]
3/8 in
[9.5 mm]
MIN
3/8 - 1 in
[9.5 - 25.4 mm]
MIN - MAX
1 in
[25.4 mm]
29/32 in
[22.9 mm]
1 3/8 in
[34.9 mm]
MINIMUM
DOOR
THICKNESS
1 in
[25.4 mm]
29/32 in
[22.9 mm]
1 3/8 in
[34.9 mm]
MINIMUM
DOOR
THICKNESS
3/8 - 1 in
[9.5 - 25.4 mm]
MIN - MAX
1 in
[25.4 mm]
29/32 in
[22.9 mm]
1 3/8 in
[34.9 mm]
MINIMUM
DOOR
THICKNESS
3/8 in
[9.5 mm]
MIN
29/32 in
[22.9 mm]
1 in
[25.4 mm]
DOOR OPENINGDOOR POCKET
DOOR OPENINGWALL WHERE DOOR OPENS TO
CLOSED POSITION
OPENED POSITION OPENED POSITION
CLOSED POSITION
TYPICAL MINIMUM OVERLAP
IN POCKET: 2 in [50.8 mm]
TYPICAL MINIMUM OVERLAP OF
DOOR ON WALL: 2 in [50.8 mm]
1 in
[25.4 mm]
2 1/2 in
[63.5 mm]
1 1/4 in
[31.8 mm]
SUGGESTED MINIMUM
1/2 in [12.7 mm]
SET BACK REQUIRED
FOR THIS OPTION
1 in
[25.4 mm]
1 1/8 in
[28.7 mm]
2 in
[50.8 mm]
MIN - MAX
15/16 - 1 9/16 in
[23.8 - 39.7 mm]
1 1/8 in
[28.7 mm]
2 in
[50.8 mm]
1 in
[25.4 mm]
1 3/8 in
[34.9 mm]
4 in
[101.6 mm]
29/32 in
[22.9 mm]
HIGH RECESSED
IN DOOR
1 in
[25.4 mm]
WIDE RECESSED
IN DOOR
Ø 3/4 in
[19.1 mm]
Ø 3/4 in
[19.1 mm]
DOOR OPENINGDOOR POCKET
OPENED POSITION
DOOR OPENINGWALL WHERE DOOR OPENS TO
OPENED POSITION
CLOSED POSITION
TYPICAL MINIMUM OVERLAP
IN POCKET: 2 in [50.8 mm]
DOOR OPENINGDOOR POCKET
CLOSED POSITION
TYPICAL MINIMUM OVERLAP OF
DOOR ON WALL: 2 in [50.8 mm]
DOOR OPENINGWALL WHERE DOOR OPENS TO
